|search engine by freefind||advanced|
Someone in Europe is using this German gypsum plaster:
and ChemmerBuster has been programming it with the Nov16 Pgm!
I get that this plaster will not take any other resin pgms (except for the Water-Charging pgm of course). I also get that most plaster will not take the Nov16 Pgm. But this one does. Why? I suspect some additive.
The co. südharzer gipswerk gmbh does come up in google but i have not tried to find more info there.
Too cool! Now the Nov16 Program CAN go into any regular plaster of Paris, BUT it is not worth doing as the energy would not be good.
UNLESS you mix some concrete in with it. Then it makes for energy equivalent to the same pgm in resin.
This morning i mixed up approx:
5 qts DAP brand plaster of Paris
2 qts sand
3 qts bionized sand
3-4 quarts Portland cement
I put on a dusk mask and some rubber gloves, and mixed all this together in a big plastic tub. The cement and plaster was a few months old and had clumps which i endeavored to break up. Then i added enough water for the right consistency, and continued to mix well by hand.
After a few minutes of doing this it started to set up pretty fast. I had to throw clumps of the mix into a 5-gallon bucket and pound them down with my fists. They were like modeling clay already.
Then i smoothed the top surface somewhat flat and level as best i could. Within a minute it was already too hard to work.
And now the clump feels pretty hard already.
Then i had to drive into town. In the prcocess of course, crossing paths with a number of repticlones. I found that when i wand them now with the Channel Program, it has a much stronger effect thanks to the boost in the Nov Pgm. It seems to crater their energy within seconds so that the Hive Mind energy no longer flows through them. Meaning they are doomed.
That is over 2.5 gallons yield.
My impression now is one could use less plaster and more cement. And this ratio may continue to change toward accommodating more concrete. Which is good as plaster costs much more. And concrete is more weather-resistant.
But if one was in love with plaster one could add 1 part Portland cement for every 4 parts of plaster.
Also my impression is, this stuff is only 95% as good as resin with the Nov16 Pgm. However, if you use bionized sand, the synergy more than makes up the difference. So you end up with real potency.
Yet, there is no particular synergy between bionized sand and RESIN with the Nov16 Pgm. The synergy is between the programmed concrete and the bionized sand. Even 3-4% in the mix should make a big difference.
This one has
5 qts Portland
2 qts plaster
3 qts sand
3 qts bionized sand
the Nov16 Pgm
The Nov16 pgm does not seem boostable by embedding other stuff. EXCEPT some compatible Luke-coil cores! Providing the pgm is in concrete/plaster instead of resin. Also, maybe the Luke core should be devoid of resin.
I inserted this baby:
https://loohanforum.orgoneitalia.it/vie … 3790#p3790
which also contains no resin. So this whole unit contains no resin, because none would improve it.
I used a bit more water this time. With the decreased % of plaster, and a bit of extra water, it did not set up as fast. But still significantly more quickly than pure concrete.
I just poured the following mix, which is getting the Nov16 Pgm:
7 qts Portland Cement
1 qt plaster of Paris
4 qts sand
2 qts bionized sand
(I had to massage out a lot of lumps.)
In this i embedded
4 wands like this:
8 concrete ice cubes with the concretite pgm
+ handfuls of old plaster pieces with the Water Charging Pgm
These ingredients go together well.
Pic in a few days.
Here it is:
Even with only that small amount of plaster, the concrete came out of the bucket as soon as i upended it yesterday.
With pure concrete, my experience is it wants to sit in the bucket for a month or 2 before letting go.