Loohan Forums

This bulletin board is associated with the website loohan.com and its blog.
Permission is required to post. No agents need apply.
Posts in the wrong category will be relocated.

You are not logged in.

search engine by freefind advanced

#1 2017-11-07 23:19:14

Tree
Enabled users
Registered: 2017-11-01
Posts: 2

Violet Flame creation

Hi all! New to the forum and hope to get acquainted to you all!
Been experimenting with the committee and created some violet flame gifting pieces last night!
I wanted to share this process I did if anyone else wants to give it a try.

I used epoxy resin for this Orgone.
-325 copper powder
I used this silicon mold of 24 little domes. Can be purchased for a couple bucks on amazon. I love the feel of the dome Orgone.
IMG_2020.jpg

So I poured the mixed resin in the mold and had the committee put violet flame pgm.
And a few min after I finished pouring I was told to go get this industrial black light I had that emits pure uv light. So I did and turned it on to let it cure under the light as well. 
Well... it amplified the energy of these by a lot! 

Here's a pic of them drying.

IMG_2028.png

This next one I circled 3 that I poured a few hours later and it didn't have the uv on it as long. But it's the same copper. 


IMG_2026.jpg

You can see that the resin absorbed the uv rays.
Other things I do while curing after committee programming is attune the resin using tuning forks to the frequencies of the earth 136.1 hz
And 528 hz.

This causes the resin to vibrate and attune to the healing frequencies.
I also like to sing to the Orgone and play my guitar tuned to 444hz to love on it will it's curing.
Anyway, they came out feeling awesome and powerfully fueled by the violet flame.

I look forward to using this uv light more as the committee permits it.
Also note: if you try this not all black lights are real UV light. Just a florescent black light. What you want is a pure UV light type.   
I got mine about 4 years back on amazon for $200

Here's a final pic of them out of the mold.

image.jpg

IMG_2029.jpg

IMG_2032.jpg

Offline

#2 2017-11-08 08:11:28

Loohan
Administrator
Registered: 2014-10-31
Posts: 4,909

Re: Violet Flame creation

I doubt all that stuff makes it any better than if you just poured plain resin into the molds and let them cure normally.

Offline

#3 2017-11-08 09:24:40

mvinon
Enabled users
Registered: 2016-03-31
Posts: 43

Re: Violet Flame creation

Welcome aboard Tree, btw cheaper uv lights are available if you search for reptile light bulbs as they are uv.

Offline

#4 2017-11-08 14:33:03

Loohan
Administrator
Registered: 2014-10-31
Posts: 4,909

Re: Violet Flame creation

mvinon wrote:

Welcome aboard Tree, btw cheaper uv lights are available if you search for reptile light bulbs as they are uv.

I think those are very expensive, and pretty full spectrum including a lot of UVA and UVB. And they say replace them after 6 months as the UV weakens.
In any case, i doubt UV does anything for resin, at least not if it's Committee programmed.

Offline

#5 2017-11-11 17:37:04

Tree
Enabled users
Registered: 2017-11-01
Posts: 2

Re: Violet Flame creation

Well.. i have came to understand myself that putting more loving energy intentionally into things I create it transmutes the energy into the materialistic object.
There's a test y'all can do yourselves if you would like to experiment for yourself:

Take 2 piece of bread, fruit, or what ever natural food you would like that decomposes.
Put each on a plate and everyday when you wake up, tell one piece of food how much you love them and are thankful for the energy it provides etc, (what ever you would like that is loving) and the other tell it how much you hate it and wish it were dead... etc.  bad stuff to the food.   
Over the course of I'd say two weeks or less. Watch how each food reacts as it starts to decompose.
You will find really cool results if your intentions during the whole test are right. 

That being said. I take that knowledge and use it in the works I create. 
Thats why I talk to my Orgone and even sing sometimes! It's a creation that I bring into existence with the help of my guides, higher selves, ET, energies all transmuting the energies that program the purpose for the piece, as I physically build it. So I put as much love into what I create as I can. 
I even use the frequency of love which is 528hz and as the piece cures I find that the resin attuned to the frequencies of the tuning fork. Just like if you put a tuning fork on your sternum or pineal gland you body gets attuned to the same frequency.  It might not stick long if ones body is really out of tune but none the less it's fact that it happens.

Loohan wrote:

I doubt all that stuff makes it any better than if you just poured plain resin into the molds and let them cure normally.

I don't think you quite understand the purpose of what I do extra. It doesn't change the committees programs at all. The programs remain the same. And they work on the energetic planes to give effect to the physical world. But the addition of healing frequencies and uv is to help do work on the physical plane within the radius directly around the location of Orgone.
So if I have Orgone in my home or it's gifted to another...the committee programs to do work on the energy plane and I can help attune physical plane healing methods...I feel the addition would not deminish any effects but strengthen. 

By all means if it doesn't resonate with you that's ok! But for me personally I feel more buzz with adding the healing frequencies of uv light and sound. And alone not in Orgone they have healed my body a great deal. I was close to physical death the past February but learned all by myself by looking inward on how to heal the body. I learned how to use sound and light.
I'm very sensitive to energy and as well as sound. I'm learning more and more about and will share as I come to more understandings looking inward.

I see your committee and yourself best programs for defense and protection.
Whereas my speciality is healing Orgone.  Before the committee added a program into an Orgone we made together it was strong with healing vibes. But after the added protection from programs has amplified it even more.

If you need any sciencey info on why the things I do add healing effects I would love to help anyone gain more understanding.


Loohan wrote:
mvinon wrote:

Welcome aboard Tree, btw cheaper uv lights are available if you search for reptile light bulbs as they are uv.

I think those are very expensive, and pretty full spectrum including a lot of UVA and UVB. And they say replace them after 6 months as the UV weakens.
In any case, i doubt UV does anything for resin, at least not if it's Committee programmed.

Yes the uv light was expensive. I did not get it for Orgone I got it for my house originally becuase I really like the effect. I like how much it emits and I'm sure smaller bulbs do emit but like loohan said a lot more of spectrum. 

The resin I use which is called excopoxy uv, which is uv resistant and all plant based (I don't like chemically  smell of polyester resin)
So just based off obersvstion the uv that is absorbed while curing gets permanently placed inside the resin.
So it just adds a small source of uv frequency to help heal the body. Nothing to do with committee programming but I'm sure there's ways they could use that to their advantage. I have not came across that info though.

Offline

Board footer

Powered by FluxBB